Fonderia D'Arte Massimo Del Chiaro

Del Chiaro Art Connection

Italiano English Français Tedesco Spagnolo Russo

Wax

Inside each single component of the negative mold, the craftsman spreads a layer of wax, after which the form is closed and the inside of the refractory (called the “core”) is filled up; at this stage, the mold is broken down (first the plaster and then the rubber) so that the wax reproduction can finally emerge. After examining it, the craftsman removes any imperfections left over, and then the artist adds his final touch to it.
A wax sculpture is not always visible as a whole. It depends on its size (e.g. the figure of Umlauf) and on its complexity (e.g. Romano’s ‘Medusa’).
Sometimes, after its original copy, the entire work of art will be able to be seen only in bronze.
The craftsman puts the pouring channels, or sprues, on the original wax copy (reed and/or wax pipes); the positioning of these pouring channels is an extremely difficult task, fundamental for achieving a perfect cast: in other words, it has to ensure that the metal reaches even the smallest cracks and holes.

Once the pouring channels have been out into place, it must all be covered with the refractory so that the sculpture takes on the shape of a mold, and the refractory perfectly takes the impression of the wax, thereby becoming the sculpture’s matrix. The refractory ‘mold’ is fired in the kiln for several days and in fact, it is in this period that the wax goes up in smoke (in other words, it loses itself, an expression from which the definition “lost-wax process” is derived). The pourings burn up, too, leaving the channels in their place which the metal will pass through to reach the empty or void spaces left by the wax. This is the original lost-wax casting process that is different from other methods and technologies, such as sand casting flask and shell casting. The latter method, invented in the US for the arms’ industry, has been re-adapted for use in art castings.
Until twenty-five years ago, kilns were made of terracotta bricks, and they were walled up and torn down every time they were put to use, depending on the size of the sculptures; in other words, they were built each time in order to enclose the refractory molds. It was like building and destroying a small house each time. When this phase of work had to be carried out, work shifts had to be organized to reach a productive cycle of 12-14 hours, beginning at dawn and finishing late in the evening.
The kiln that had just completed the firing of the refractory molds had to be taken down (after days and days of hard work), the molds taken out and replaced with those that still needed firing; and then once again, the new kiln had to be rebuilt around the new molds.
In 1983, Massimo Del Chiaro planned a kiln that was similar to the one used for pottery, though three times as large, which could completely avoid the building and destruction of its walls and “roof”. Nowadays, the whole process takes only eight hours.
The phase of replacing the molds is particularly delicate as the fired refractory is extremely fragile.

 

  • The old factory’s wax retouching department

  • Charles Umlauf while giving the final touches to the wax copy of a detail of his ‘Hope for the future’ sculpture. Worth noting is the detail in the refractory’s core which one can just see in the arms’ section

  • Francesco Martani while working on the wax copy of ‘Tree of Smiles’

  • Michel Anthony while working on a wax copy of a sculpture dedicated to the theme of peace

  • Massimo Del Chiaro while applying the pouring channels or sprues

  • One of Sandro Chia’s work while it is being covered with refractory; from the left: Marcello Barsi (Foundry craftsman), Sandro Chia and Massimo Del Chiaro

  • Detail of the wax head of Umlauf’s ‘Madonna with Baby’, with its pouring channels

  • Charles Umlauf’s ‘Madonna with Baby’ due to its considerable size (about three metres high) was cast in two parts; in this picture, you can see the refractory cover after the pouring channels have been applied and in particular, the refractory core inside the section of the legs.

  • This photo shows how work was carried out before the new kiln was created by Del Chiaro. In the background, you can just see a craftsman intent on taking out the fired molds from the destroyed kiln; at the front of the photo, you can see the refractory ‘molds’ wedged inside the iron and sand containers while waiting for the bronze pouring; on the right, another kiln actively working.

  • Seated man on a stool, 2016

    Seated man on a stool, 2016

    Sean Henry
    Bronze, wax of the first copy, detail of the head
    300 x 190 x 155 cm
    Edition 1/3

Via delle Iare, 26/B C.P. 191
55045 Pietrasanta (LU) - Italy
P.IVA 01942980465
  Copyright © 2011
Fonderia D'Arte Massimo Del Chiaro.
All rights reserved.
Privacy and Cookies
Cookies Settings
  Tel. +39 0584 792955
Fax +39 0584 792940
E-mail fonderia@delchiaro.com